Now some may find no need for that extreme an adjustment but if you are not built like the ‘average man’ –say you’re not 5’9” , 180 pounds and male–all that adjustment is more than handy. It’s essential to good fit and good fit is essential to accurate, stress-free shooting. It’s something the 99% of us who aren’t ‘average’ have been waiting for.

[192] Human Rights Watch is aware of one Department of Environment study that includes data from wastewater samples of Hazaribagh tannery effluent. That study found that Hazaribagh wastewater vastly exceeds Bangladesh’s permitted standards for tannery effluent. Department of Environment, “Survey and Mapping of Environmental Pollution From Industries In Greater Dhaka And Preparation Of Strategies For Its Mitigation,” September 2008, p. 62. Copy on file with Human Rights Watch.

[206] The methods identified include salt-free raw hides and skins, hair-save liming, ammonia-free de-liming and bating, and advanced chrome management systems. See United Nations Industrial Development Organization, “Introduction To Treatment Of Tannery Effluents: What Every tanner should Know About Effluent Treatment,” 2011, p. 6. Copy on file with Human Rights Watch.

However, the picture changes a bit if you are assembling a structure using fillet or lap welds. While groove welds normally are loaded in tension and usually fail in the HAZ (as stated above), fillet welds are almost always loaded in shear and fail right in the middle of the weld. In this case, the difference in strength between 4043 and 5356 does matter. The minimum shear strength of 4043 usually is listed at 11 kilopounds per square inch (KSI), while the shear strength of 5356 is listed at 18 KSI. In the case of a structure assembled mainly from fillet welds, 5356 does have a strength advantage.

The population could be even better if flounder spawning success wasn’t tied to weather. Cooler winters result in a more prolific flounder spawn. Mild winters combined with added fishing pressure somewhat stifled the population surge. But stocks remain strong.

Bangladeshi governments have contemplated relocating the Hazaribagh tanneries for almost two decades.[65] One Ministry of Labour official said he had been hearing about such a move since he began working at the ministry in 1993.[66]

VW suffered its equivalent of the ‘difficult second album’ syndrome when it came to following the original Golf GTI in 1983. In fact, it wasn’t until the fifth incarnation, a decade or more later, that the tunes were anything like as memorable. Core to this transformation was a new chassis, which replaced the previous car’s unlovely beam rear axle with a fully independent set-up, and the surprisingly characterful blown 2.0-litre TFSI engine that made 197bhp. VW’s dual-shift DSG also arrived in this era, a slickly digital set-up that served notice of where things were headed even if the manual was still more fun. Clearly, the Golf had grown somewhat in size by this stage in its career, and the MkV iteration definitely errs more on the thoughtful side. But it’s also a car that moves with a rigorously engineered harmony, and it proved unexpectedly useful on track. Finely balanced, expertly judged. 

For years, consumers have tossed soda cans, detergent bottles and greasy pizza boxes into recycle bins, feeling they’ve made some contribution to the environment. Some washed or rinsed containers and followed long-standing guidelines on plastic containers. But many do not follow guidelines. Or, they toss non-recyclable trash in curbside bins and trust that someone, somewhere will clean and sort it all out.

That scale can measure up to 300kg/600lbs. I was not expecting the connections to be that strong so my setup was clearly not prepared. I would like to build a hanging set up for testing things like this in the future. I think you’re missing the point of my video. Most people do not need connections strong enough to pull CF tubes in 2. I just designed an easy way to make customizable rod ends that are plenty strong for hobby projects/robotics.

There is a Memory button on the top left of the control panel, which allows you to save nine programs in DC TIG, nine in AC TIG, nine in DC Stick, and nine in AC stick. If you do a certain type of weld repeatedly, these memory settings can be very helpful.

There are a few more tweaks you can make in this setup menu, but I have covered the features that I think our readers will most appreciate. Let me know if you have specific questions, and perhaps they can be addressed in future Professor Hammer columns.

[74] Human Rights Watch interview with Sheikh Fazle Noor Taposh, member of parliament for Hazaribagh, Dhaka, June 10, 2012.